Personal Spot Welder Yokodai.JPYokodaiJPYokodaiJP���S�X�y�[�XYokodaiJP

Go to Yokodai.JP's Home Go to SpotWelder's page Go to Support page Go to Contact us Go to Other Products Go to YJP's Store
Go to Yokodai.JP's Home Go to SpotWelder's page Go to Support page
Go to Contact us Go to Other Products Go to YJP's Store

 

 

Principle of Spot Welding

Our welder's Capability

How-To-Use Our welder

Welding Stainless Steel

Thermocouple Welding

Welding with Nickel Plates

Welding with Metals
e.g. Aluminum, Steel, Phospate Bronze

Product Comparison

< PRODUCTS >

Spot Welder HSW-01A

Spot Welder HSW-02A

Spot Welder HSW-03

Optional Accessories

Recommended Packages

Nickel Plates

Price and Purchase

User's Voice

F A Q (General)

FAQ(Technical)

YOKODAI.JP SPOT WELDER OPTIONAL ACCESSORIES

safety glass
Safety Eyewear HSW-G1

   

Safety Eyewear HSW-G1

In a proper welding, as long as the distance to the face is kept around 50 cm, then the sparks produced would not be so dangerous. However, on welding without enough pressure applied to the welding pen, or welding stainless or iron, sparks and small pieces might fly off. Please use safety eyewear to protect the eyes in these situations.

HSW-P1S�ʐ^
Welding Pen HSW-P1N

   

 

HSW-P1S Welding Pen for HSW-01A
(Included in HSW-01A standard package)

If the heat from the welding point is ideally released to the welding pen, then the welding pen would not be accidentally welded to the nickel plate. However, due to inadequate plunge pressure of the welding pen, sometimes they might be accidentally welded. Normally, the welding pen can be restored by cleaning the tip, but if during frequent use, it may be necessary to replace the welding pen.

welding electrode
Welding Pen HSW-P1N

   

 

HSW-P1N Welding Pen for HSW-02
(Included in HSW-02 standard package)

If the heat from the welding point is ideally released to the welding pen, then the welding pen would not be accidentally welded to the nickel plate. However, due to inadequate plunge pressure of the welding pen, sometimes they might be accidentally welded.

Normally, the welding pen can be restored by cleaning the tip, but if during frequent use, it may be necessary to replace the welding pen.

PSW-0P2�ʐ^
Welding Stick HSW-P2

   

Welding Stick HSW-P2
For HSW Series Non-Adhesive Welding Pen

Chrome cord is used for the electrodes, making it strong against wearing off, and difficult to adhere. The grip is larger than normal, making it easy to operate.

Release the electrode tip to replace.


Welding Pinset HSW-W2

   

HSW-W2 Welding Pinset for HSW-01/02

This electrode can pinch the welding materials. With 120 mm of length, it guarantees a 5 mm of distance between electrodes. It can be used by connecting it to the connector which is used for the welding pen.

 

HSW-EB1
Stick Electrode HSW-EB1

   

 

HSW-EB1 Stick Electrode for HSW-01/02

This is a Stick Electrode for HSW Series. It can be used to replace one of the welding pens.
Using this, an improved process and strong welding due to the large current can be achieved.
10 mm of angle, length 98 mm, screw hole for electric cord fitting�fs outer diameter 5 mm

 

foor switch for HSW
Foot Switch HSW-F1N

   

HSW-F1N Foot Switch for HSW-01/02/03

When welding alone, holding welding pens with both hands will make it difficult to push the trigger switch. It is possible to trigger the spot welder by using this foot switch connected to the welder foot switch rear panel connector.

*) There are black, white, and red for the switch color, but you cannot choose the color.

PowerController�ʐ^ Power Controller HSW-PC1

   

 

 

 

 

HSW-PC1
HSW-PC1 Power Controller for HSW Series

This is a Power Controller designed for HSW Series. This machine is to be connected between the spot welder and the power adapter and by doing so the voltage supply to the spot welder can be adjusted.
Different from a normal voltage altering equipment, even when lowering the output voltage, the welder voltage can be lowered really fast.
Welding with stainless thin line and mesh, and also thermocouple need this to control the power as not to break the materials down.

[SPESIFICATIONS]
Input Voltage Maximum 25 V
Output Voltage 2 V - 25 V
Output Current Maximum 3 A
(as when connected to welder HSW-01A/02A)
Recommended Room Temperature 0 - 35 degrees C
Humidity 10% - 90% (non-fogging)
Measurement 80 (W) x 30 (H) x 50(D) mm
excluding protrusions)
Connector shape Inner diameter: 2.1 mm - Outer diameter: 5.5 mm

*) As explained above, this machine alters voltage supply. Thus, this machine will not affect the welder's capability upper limit.